آہ! رشید احمدصدیقی
ابھی مولانا عبدالماجد دریابادی کی وفات کا غم تازہ ہی تھا کہ اردو زبان کے ایک اور صاحب کمال صاحب طرز اور صاحب فن ادیب اور انشاء پرداز یعنی یگانۂ روزگار، فخر مسلم یونیورسٹی علی گڑھ درمایۂ ناز فرزند شیراز ہند جناب رشید احمد صدیقی کی رحلت کی خبر ملی۔
دل سے لپٹ لپٹ کر غم بار بار رویا
وہ مڑیاہو ضلع جونپور کے رہنے والے تھے، علی گڑھ میں چھ سال تعلیم پائی، یہاں کے شعبۂ اردو کے صدر کی حیثیت سے سبکدوش ہوئے تو یہیں کے ہوکر رہ گئے، اس کی روایات کے رازداں، اس کی حمیت کے دیدباں، اس کی عزت کے نگہبان اور اس کی آبرو کے پاسبان بن کر ساری زندگی گزاری، وہ علی گڑھ مسلم یونیورسٹی کو ایک اہل دل مسلمان نقاش اور مصور کا شاہکار سمجھتے رہے، سیاحوں کو جو دل آویزی اور رعنائی اجنٹا اور ایلورا میں نظر آتی ہے، وہی ان کو گھر بیٹھے مسلم یونیورسٹی میں نظر آتی رہی، شاہجہاں مثمن برج میں بیٹھ کر تاج محل دیکھا کرتا، پھر اسی برج میں اس نے ایک چھوٹا سا شیشہ نصب کرا رکھا تھا، جس میں تاج محل کا پورا عکس پڑتا رہتا، رشید صاحب کے لئے علی گڑھ میں ان کا مکان ان کا مثمن برج تھا، جس کے اندورونی حصہ میں ایک خوبصورت لہلہاتا سبزہ زار تھا، اس کے بیرونی حصہ میں طرح طرح کے گلاب کے پودے لگے رہتے تھے، یہیں سے اپنے شیشہ دل میں اپنے ذہن کے تاج محل یعنی مسلم یونیورسٹی کو دیکھ کر خوش ہوتے رہتے، اب اسی تاج محل کے اندر مدفون ہیں، جس کی سرزمین نے ان کے جسدخاکی کو نہیں بلکہ مسلم یونیورسٹی کے نشاط روح، سوزسینہ اور دل بے قرار کو بڑے شوق سے اپنی آغوش میں لے لیا ہوگا، وہ جاچکے مگر اپنی...
Islam is not a mere set of worships but it leaves no stone unturned to guide its followers regarding the social conduct be it politico-legal, sociocultural or economic etc to name a few. The interest-based transactions have been categorically rendered impermissible and unlawful by virtue of Quranic injunctions and authentic ahadith. In this article the issue of interest based transactions – Muslim to Muslim, Muslim to non-Muslim and vice versa, a Muslim resident of a non-Muslim state and a Muslim non-resident of a nonMuslim state – has been discussed in detail in the light of Quran, hadith and juristic rulings of the eminent Islamic scholars including the great four imams.
Multilayer Flood-welding repair of hot forging dies is a very useful technique which can remarkably enhance the working life of the die. Conventional quenched and tempered dies do not exhibit good resistance to wear. Therefore, these dies are nitrided to improve wear resistance but after the production of few numbers of forgings cracks are produced. That’s why here multilayer flood-welding technique has been adapted to improve the die life and to establish the optimum parameters for this technique. In the current work, the modified H12 hot-work tool steel was weld deposited in the cavity of hot-forging dies and their performance was monitored visually for the die condition and with the macroscopic and microscopic examination. It was analyzed that the thicknesses of the both hard upper ‘capping layer’ and intermediate ‘buffer layer’ have a prominent influence on the performance and the life hot forging die. For a particular dimensions and contour of the die impression, there came out an optimal thickness of the capping layer that provided the best performance. Further increase in capping layers thickness exhibited brittle cracking, whereas thinner capping layers produced early wear and plastic deformation. For intermediate buffer layer, in order to provide adequate backup support to capping layer, a certain minimum thickness level is required. This process minimized the die steel consumption because the thickness of the forging die is not reduced in the process of reworking and ultimately the process is cost effective. Moreover, the Multilayered flood-welded dies were gas nitrided to further enhance the life of the forging die. The results have shown that double stage nitriding process is good for these dies which produced minimum compound layer on the nitrided surface. The die life as a result of nitriding was amazingly increased compared to normal Multilayered flood- welded dies. The dies showed very slow wear and thermal fatigue cracking after the production of large number of forgings. By employing these dies excellent overall surface finish of the forged parts was achieved.